OCTAVE V 40 SE The All-rounder
€4,650.00
The V 40 SE is a line level integrated amplifier with 2 x 40 W peak output power. He is a further development and direct descendant of the successful V 40 and V 50 amplifier models. His powerful, clear bass fundamentals and his captivating resolution in the high frequencies win much respect. His unique features lift the V 40 SE into the 21st Century, while his performance earned him the rare “Stereoplay Highlight” (issue 07-2009), a prestigious award bestowed by the German high-end audio magazine Stereoplay.
Description
| Features | |
 In – and Outputs
The V 40 SE features a total of five single-ended (RCA) inputs (including the Home Theatre Bypass input). Outputs included are one RCA Record output, one regulated Preamplifier output and one Loudspeaker output. Black Box Connector OCTAVE, with the Black Box technology, offers an upgrade path for optimizing the OCTAVE amplifier in respect to the speaker. This flexibility is a unique feature of the OCTAVE brand. The dynamic and tonal stability of an amplifier is strongly dependent upon the stability and capacity of the power supply, therefore the Black Box and Super Black Box were developed as external upgrades to the OCTAVE amplifiers’ power supply storage capacitors by increasing their capacitance by a factor of 4 (Black Box or 10 (Super Black Box), respectively. This is a tremendous benefit if the speaker is difficult to drive. Loudspeaker efficiency is made less critical, while the amplifier is enabled to handle speakers with extremely low minimum impedances. Ecomode A forward looking feature of OCTAVE is the unique ECOMODE power saving electronic circuitry developed to reduce heat and unnecessary power consumption when the amplifier is switched on but not in use. This electronic system controls the power condition and reduces power consumption when the amplifier does not receive a signal for a period exceeding 10 minutes. In this “sleep” mode, the V 40 SE draws only 20 W idle current. Virtually no heat is produced by the unit, and the heater voltage and the high voltage for the power amplifier section are switched off. When a signal is detected by the V 40 SE, the Ecomode circuit will turn the amplifier back on, with a warm-up/start-up delay of approximately 30 seconds before the unit will operate. Ecomode also serves to increase the lifetime of the tubes, while having an added benefit of improved safety allowing the V 40 SE owner a level of security against any problems when leaving the unit powered on. BIAS Adjustment The Output stage of the V 40 SE operates in Class A/B, and therefore requires an adjustable BIAS regulation. The highly sophisticated yet extremely simple yet accurate BIAS calibration system is accessed on the front panel of the unit. It utilizes external precision bias trim pots and LED confirmation, allowing the user to readily monitor the output tubes and simply correct their bias individually at the front panel – without the need of a micrometer let alone any special knowledge or tools. The correct BIAS is vital for the constant sound quality of the V 40 SE. Due to this facility there is no need for a technician to service the V 40 SE for changing or tubes or to check their condition. The precision of this user friendly system is within 0.5% accuracy.
Power Management and Protection System The V 40 SE is equipped with a multi-stage Soft-Start/Turn-On protection circuit which extends component as well as tube life considerably by protecting against stress caused by typical high inrush currents during switch-on. The unit starts in a defined sequence, with the Protection System monitoring the V 40 SE completely, and activated whenever a malfunction is detected. Once the Protection is activated, the V 40 SE is powered down. |
|
| The V 40 SE output stage consists of two power pentodes (Type 6550) for each channel. Due to the BIAS Control and Monitoring System, the use of other pin-compatible output tubes is possible to match the amplifier to personal taste, or to benefit from new or improved tubes.
Like all OCTAVE Amps the, V 40 SE is based on the enhanced pentode configuration. This configuration ensures the absolute stability of the amplifier against the unstable impedance of the loudspeaker. Impedance mismatch is without consequence, and the V 40 SE is stable down to a 2 Ohm Load. An important contributor to this stability is the single impedance output transformer. The V 40 SE is the perfect amp for speakers with an average efficiency rating.But not only is the low impedance capability an advantage, with his exceptional Signal-to-Noise ratio of –110dB / Full Power he is also an ideal partner for high efficiency loudspeakers. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Related products
Pathos Classic Remix
Pathos Classic Remix – Integrated amplifier
Beauty as a unifying element, the universal language beyond of culture, age, nationality, a noble force able to remove the barriers and put in contact with humanity.
Beauty of sound, beauty of craftsmanship, beauty of technology, the beauty of the novelty, beauty of style and design, beauty as an ambassador of a confirmation for those already familiar with the Pathos, or ambassador of the Pathos values for all others that who will find in a new and perfect balance of lines, materials, and technologies, all iconic elements tradition Pathos albeit in a more contemporary formula revisited, in a word: ClassicRemix!
Finishes: Matt Metalic black – €2600, Lacquered white, black, red and zebrawood – €2970
LINE MAGNETIC LM-503PA
LM-503PA – Mono Amplifier – Single Ended 845 – 1x24W (Price for a pair)
The LM-503PA monoblocs have been created from an original design of Western Electric. It uses a single ended 845 output stage with Full Music 300B drivers. Pre-amplifier stage uses a special Line Magnetic tube, the 310A.
The rectifier tube is a 5U3C and the power line is filtered by two special chokes. User bias controls for 300B and 845 are used for bias adjustment with a specific VU meter to allow you to monitor bias with ease.
LINE MAGNETIC LM-513PA
LM-513PA – Mono Amplifier – Push Pull 845 – 1x160W (Price for a pair)
The mono amplifier LM-513PA is a Push-Pull amplifier with 4x 845 tubes in pure Class A amplification and delivers 1x160W. The use of high-quality components (Multicap, Philips BC filter, Motorola) hand-made construction with the finest point-to-point wiring for the most part is the guarantee of exemplary reliability.
LINE MAGNETIC LM-845 Premium
LM-845 Premium – Integrated Amplifier – Single Ended 845 – 2x30W
The LM-845 Premium is the result of many years of research on the 845 triodes Single Ended design. Thanks to its exceptional design and manufacturing quality, it is fast becoming the absolute reference in the high-end amplifiers world. With a power output of 2x30W, it can be used with most of the existing reference speakers.
The LM-845 Premium is a combination of two units: One is the amplifier unit and the other is Outputs unit. In the amplifier unit the main amplifier and power supply parts are included while in the outputs unit output transformer and speaker outputs parts are included.
Amplifier unit and outputs unit are connected with two separate well-built connectors and cables for which you can put up and down or left and right.
All tube Integrated with 12AX7 input tubes, 310A signal amplification stage, 300B driver tubes and 845 output tubes. Well selected and matched tubes. Tubes we chose are Shuguang 12AX7, Line Magnetic 310A, Shuguang 300B and Shuguang 845.
Two user bias controls for 300B and 845 have been used for bias adjustment and two meters has been added to the front plate to allow you to monitor bias with ease.
Negative Feedback switch is on the front plate that you can choose between two levels of NFB to enjoy the different sound outputs.
In LM-845 Premium it includes eight transformers. Two pieces of power transformers, two output transformers, two coupling driver transformers, two chokes. In order to have a stable and better power supply, we have designed two pieces of specially designed Toroid power transformers in Balance. EI type of output transformers is installed in the outputs unit separately to lower interfere from the external radio frequency.
ATC SIA2-150
SIA2-150 – Stereo Integrated Amplifier
- 150 watts per channel.
- Class A/B operation.
- Hand built in the UK.
- 5 RCA inputs.
- Record, sub and pre outputs.
- Headphone jack.
- Remote control.
- 6 year warranty.
Pathos Inpower
Pathos Inpower – Monoblock Power Amplifier
InPower monoblock power amplifiers represent the evolution of the INPOL® circuit, originally created with the birth of the T.T. integrated amplifier.
The purpose of InPower project was to design an amplifier able to drive all loudspeakers.
Even in spacious listening environments. All this with the same state-of-the-art sound quality which has been universally bestowed upon the T.T.
Pathos Ampli D
Pathos Ampli D – Power Stereo Amplifier
AmpliD is the first of a new line of digital amplifiers from Pathos. Completely balanced in D Class, it features a 70 Watt output power on each channel at 8 Ohm, and 130 Watt on each channel at 4 Ohm; it has 2 kinds of inputs (1 as stereo balanced XLR and 1 as stereo unbalanced RCA line).
Despite small dimensions, AmpliD provides great power and high sound quality. It reached state-of-the-art among all those digital amplifiers, that cannot be underestimated in terms of technological innovation.
Finishes: Grey or Black with buttons
LINE MAGNETIC LM-201IA
LM-210IA – Integrated Amplifier – Single Ended 300B – 2x8W
The integrated amplifier LM-210IA is a Single Ended amplifier with 2x 300B tubes in Class A amplification and delivers 2x8W.
Output transformers are oversized. Listening, the magic of the 300B is total both in the richness of the timbres and the subtlety of the sound scene.
GLOBAL VIEW
Class A amplifier 2x8W RMS
Input stage: 2x 12AX7 Rectifier: 2x 5U4G Drivers: 2x 310A Power stage: 2x 300B