LINE MAGNETIC LM-211IA
LINE MAGNETIC LM-211IA
€1,590.00
LM-211IA- Integrated Amplifier – Push Pull EL34 – 2x32W
The Line Magnetic integrated amplifier LM-211IA is a push-pull amplifier with 4x EL34 tubes in Class AB amplification and delivers 2x15W in triode mode and 2x32W in ultra-linear mode. It has 4 balanced line inputs and 4/8Ω output groups.
The rear-illuminated front panel meter is used to adjust polarization of the tubes. The use of high-quality components (Realcap capacitors, ALPS potentiometer) wired in the air, for the most part, is the guarantee of exemplary reliability. Its transformers output are of EI type, specially designed for power supply. The LM-211IA delivers dynamic, rich and natural sound.
Description
Highlights:
Specifications
Class AB amplifier
2x15W RMS Triode 2x32W RMS Ultra-linear
Tubes: 2x 12AX7, 2x 12AU7, 4x EL34
THD: 1% (1kHz)
Signal/Noise ratio: 88dB (Weighted A)
Frequency response: 10 à 50.000 Hz (-1.5 dB)
Sensitivity: 200 mV (Built-in Mode)
Input Impedance: 100kΩ
Load impedance for HP to connect: 4/8Ω
Related products
LINE MAGNETIC LM-503PA
LM-503PA – Mono Amplifier – Single Ended 845 – 1x24W (Price for a pair)
The LM-503PA monoblocs have been created from an original design of Western Electric. It uses a single ended 845 output stage with Full Music 300B drivers. Pre-amplifier stage uses a special Line Magnetic tube, the 310A.
The rectifier tube is a 5U3C and the power line is filtered by two special chokes. User bias controls for 300B and 845 are used for bias adjustment with a specific VU meter to allow you to monitor bias with ease.
Pathos Inpower
Pathos Inpower – Monoblock Power Amplifier
InPower monoblock power amplifiers represent the evolution of the INPOL® circuit, originally created with the birth of the T.T. integrated amplifier.
The purpose of InPower project was to design an amplifier able to drive all loudspeakers.
Even in spacious listening environments. All this with the same state-of-the-art sound quality which has been universally bestowed upon the T.T.
LINE MAGNETIC LM-513PA
LM-513PA – Mono Amplifier – Push Pull 845 – 1x160W (Price for a pair)
The mono amplifier LM-513PA is a Push-Pull amplifier with 4x 845 tubes in pure Class A amplification and delivers 1x160W. The use of high-quality components (Multicap, Philips BC filter, Motorola) hand-made construction with the finest point-to-point wiring for the most part is the guarantee of exemplary reliability.
LINE MAGNETIC LM-88IA
LM-88IA – Integrated Amplifier – Push Pull KT88 – 2x42W
Forty-two watts per channel, Class AB Integrated Stereo Amplifier with KT88 output power tubes, 6CL8A and 12BH7 input tubes. Tubes we selected for the amplifier is Electro Harmonix 12BH7, Mullard 6CL8A and JJ Electronics KT88.
Well selected and matched tubes. No matter it is the Pre-stage or power stage of tubes we select and choose the best matching ones to use on the same unit of the amplifier to get the best sound quality out of it.
LM-88IA Amplifier can operate in two different ways Auto-biased or Fixed Bias. You can select the one you prefer. Power output for Auto-bias mode is 45 watts while for fixed bias it is 30 watts per channel. Once worked in Auto-bias mode it outputs a more warmth sound and go near to the way of Class A operation.
Different from other inputs Pre-In offers you a possibility to connect to some other Preamplifier so that you can the LM-88IA as a power amplifier.
Specially designed Toroid transformers made of Z11 Core for power supply and two Japanese Audio grade EI types of output transformers with wide bandwidth are applied. All transformers and chokes are encapsulated and installed separately on the amplifier to avoid and lower the disturbance between each other.
Audio Grade of components for LM-88IA: Japanese ALPS volume potentiometer, Multicap coupling Capacitors, American MIT Coupling Capacitors, German MCAP Coupling Capacitors, etc.
Finish: Black
LINE MAGNETIC LM-805IA
LM-805IA – Integrated Amplifier – Single Ended 805 – 2x48W
The Line Magnetic 805iA uses single-ended triode 805 tubes and operate in pure Class A. It delivers 2x48W power. It has 3 unbalanced line inputs, 1 bypass input and 4, 8, 16Ω output groups. The rear-illuminated front panel meter is used to adjust the polarization of the tubes.
The use of high-quality components (Mundorf N-Cap capacitors, ALPS potentiometer) wired in the air for the most part is the guarantee of exemplary reliability. Its power and current capacity allows it to manage a very wide range of speakers. The use of the legendary triode 805 offers a listening to an unusual musicality.
Pathos Inpol Heritage
Pathos Inpol Heritage – Integrated Amplifier without Compromises
InPol Heritage represents the projectual legacy of the late Pathos co-founder, designer and inventor of InPol, Engineer Giani Borinato.
The team of Pathos technical designers pushed themselves to the very highest level with this unprecedented project; an enormous amount of time was spent with this product, which is characterised by components of the highest quality and the customary absence of compromises.
The digital bias/gain set technology with intelligent control is entrusted to the same microprocessor which regulates the volume, thus guaranteeing the performance of the amplifier itself and its ability to drive the loudspeakers efficiently.
Thanks to the (optional) HiDac Mk2 converter, music lovers who want the very best from the latest digital sources will find their demands fully met.
InPol (Inseguitore Pompa Linear – Linear Pump Follower) is a system patented by Pathos Acoustics which has enjoyed great success and won many awards.
Inpol devices have a special sonic personality obtainable only by means of this particular circuit design – fully balanced in Class A using a single solid-state component in follower configuration, with high current gain and with voltage gain together. The valve amplifier amplifies the input signal voltage and InPol supplies the current to drive the loudspeakers without any further amplification. In this way, the signal is entrusted to the valves and becomes a true copy of the original, with all the quality, purity and harmonic content of the original.
This technology allows an increase in the theoretical output in pure Class A of between 25% and 50% together with a low output impedance which is fundamental for the damping factor and further improved by the double InPol.
Finishes: Anodized Black
LINE MAGNETIC LM-212PA
LM-212PA -Mono Amplifier – Single Ended 212 – 1x32W
The LM-212PA is the «ultimate» monophonic amplifier from Line Magnetic, requiring more than two years of development. Its design is based on a Triode 212 mounted in Single Ended and «drived» by a 300B. In order to guarantee the durability of this exceptional tube, a sophisticated mechanical system protects it from shocks when not in use.
Finish: Silver
LINE MAGNETIC LM-845IA
LM-845IA – Integrated Amplifier – Single Ended 845 – 2x22W
The LM-845 is a quality upgrade of the old LM-518 amplifier. It delivers twenty-two watts per channel, Single Ended design, Pure Class A Integrated Stereo Amplifier with 845 output power tubes. The drivers are 6P3P tubes, the capacitors are Multicap, American MIT Coupling Capacitors, German MCAP Coupling Capacitors,
All tube Integrated with 12AX7 input tubes for voltage amplification, EL34 driver tubes, 5AR4 rectifier tubes and 845 output tubes. Driver tubes 6P3P can also be replaced by different kinds of driver tubes and you can select which tubes you prefer judging by different sounds. Well selected and matched tubes. No matter it is the Pre-stage or power stage of tubes we select and choose the best matching ones to use on the same unit of the amplifier to get the best sound quality out of it.
Different from other inputs Pre-In offers you a possibility to connect to some other Preamplifier so that you can the LM-845IA as a power amplifier.
User bias control has been used for bias adjustment and one meter has been added to the front plate to allow you to monitor bias with ease. External Hum Balance adjustment for sound adjustment.
Specially designed Toroid transformers made of Z11 Core for power supply and two Japanese Audio grade EI types of output transformers with wide bandwidth are applied. All transformers and chokes are encapsulated and installed separately on the amplifier to avoid and lower the disturbance between each other.