ULTIMA Pre 2
€13,950.00
Eight Input Reference Preamplifier
Featuring unrivalled connectivity and minimal colouration, the ULTIMA PRE 2 can be the hub of your Hi-Fi system without taking anything away from the incoming signal.
Description
The fully modernised ULTIMA PRE 2 is built to complement stereo systems of the highest order and represents the finest Chord Electronics engineering inside and out.
Just as a preamplifier should, the ULTIMA PRE 2 adds nothing to the original waveform and instead preserves it with zero colouration. This is thanks to our latest advances in switch-mode power supply design, developed from aerospace technologies, and our ultra-low-noise proprietary solid-state circuitry which is both carefully shielded and equipped with premium system components. As a result, the ULTIMA PRE 2 is able to achieve unprecedented noise floor performance of -130dB, meaning your source will always sound like your source and nothing else.
Where connectivity is concerned, the ULTIMA PRE 2 has hi-fi systems (and more!) covered. Featuring eight inputs, four stereo pairs of XLRs for balanced connections and another four RCA for unbalanced connections, each of these can be gain-matched and individually selected. For outputs, a single stereo pair is available via XLR or RCA, to accommodate a single stereo amplifier such as the ULTIMA 5 or a pair of mono blocks such as the ULTIMA 3s. Naturally, headphone users are catered for, too, for personal and late-night listening with the addition of a high-resolution 6.35mm output on the front fascia.
Where system-triggering is important, (allowing the simultaneous start-up of connected equipment from a single button-press), the ULTIMA PRE 2 is equipped with three outputs which should be more than enough for most systems.
Technical Specification
Frequency Range:
2.5Hz – 200kHz +/- 3dB
Total Harmonic Distortion:
0.002% 20Hz – 20kHz
Intermodulation Distortion:
-115dB on all inputs
Signal to Noise Ratio:
-120dB on all inputs
Channel Separation:
20Hz @ 100dB, 1kHz @ 95dB, 10kHz @ 90dB, 20kHz @ 85dB
Channel Balance:
0.01dB
Input Max Voltage:
17v RMS Balanced – 8.5v RMS Unbalanced
Output Max Voltage:
17v RMS Balanced – 8.5v RMS Unbalanced
Output Offset:
0mV (Both Channels)
Potentiometer Performance:
0dB 0.5dB, -20dB 0.2dB, -60dB 0.24dB (13seconds Full Travel)
Nominal Gain:
All inputs subject to six levels of switchable gain – x0.5, x1, x1.5, x2, x2.5, and x3
Input Impedance:
100 kΩ Balanced – 50 kΩ Unbalanced
Output Impedance:
100Ω (Short Circuit Protected)
Operating Voltage:
85v – 270v AC (50Hz – 60Hz) Auto Switching
Power Consumption:
30w
Dimensions Without Integra Legs:
420mm (w) x 355mm (d) x 133mm (h)
Dimensions With Included Integra Legs:
480mm (w) x 355mm (d) x 173mm (h)
Weight:
18kG
Related products
LINE MAGNETIC LM-216IA
LM-216IA – Integrated Amplifier – Push Pull KT88 – 2x38W
The Line Magnetic integrated amplifier LM-216IA is a push-pull amplifier with 4x KT88 tubes in Class AB amplification and delivers 2x22W in triode mode and 2x38W in ultra-linear mode. The LM-216iA delivers dynamic, rich, and natural sound.
GLOBAL VIEW
Class AB amplifier
2x22W RMS Triode mode
2x38W RMS Ultra-linear mode Input stage: 2x 12AX7 and 2x 12BH7 Power stage: 4x KT88
Hegel HD30 (EISA Award Winner)
The Hegel HD30 is the ultimate digital control centre. It does everything you can dream of, and does so with world-class quality. There is an abundance of inputs, ranging from balanced AES/EBU and BNC connectors, to Network and USB connections – with the latter also accepting DSD signals. The built-in volume attenuator allows you to connect directly to a power amplifier or a pair of active loudspeakers. Highly advanced power supplies and careful lay-out brings the noise floor down towards a mindblowing – 150dB. In
LINE MAGNETIC LM-845IA
LM-845IA – Integrated Amplifier – Single Ended 845 – 2x22W
The LM-845 is a quality upgrade of the old LM-518 amplifier. It delivers twenty-two watts per channel, Single Ended design, Pure Class A Integrated Stereo Amplifier with 845 output power tubes. The drivers are 6P3P tubes, the capacitors are Multicap, American MIT Coupling Capacitors, German MCAP Coupling Capacitors,
All tube Integrated with 12AX7 input tubes for voltage amplification, EL34 driver tubes, 5AR4 rectifier tubes and 845 output tubes. Driver tubes 6P3P can also be replaced by different kinds of driver tubes and you can select which tubes you prefer judging by different sounds. Well selected and matched tubes. No matter it is the Pre-stage or power stage of tubes we select and choose the best matching ones to use on the same unit of the amplifier to get the best sound quality out of it.
Different from other inputs Pre-In offers you a possibility to connect to some other Preamplifier so that you can the LM-845IA as a power amplifier.
User bias control has been used for bias adjustment and one meter has been added to the front plate to allow you to monitor bias with ease. External Hum Balance adjustment for sound adjustment.
Specially designed Toroid transformers made of Z11 Core for power supply and two Japanese Audio grade EI types of output transformers with wide bandwidth are applied. All transformers and chokes are encapsulated and installed separately on the amplifier to avoid and lower the disturbance between each other.
LINE MAGNETIC LM-513PA
LM-513PA – Mono Amplifier – Push Pull 845 – 1x160W (Price for a pair)
The mono amplifier LM-513PA is a Push-Pull amplifier with 4x 845 tubes in pure Class A amplification and delivers 1x160W. The use of high-quality components (Multicap, Philips BC filter, Motorola) hand-made construction with the finest point-to-point wiring for the most part is the guarantee of exemplary reliability.
LINE MAGNETIC LM-34IA
LM-34IA- Integrated Amplifier – Push Pull AB EL34 – 2x40W
Forty watts per channel, Class AB Integrated Stereo Amplifier with EL34 output power tubes, 12AX7 and 12AU7 input tubes.
Standard with EL34 output tubes. Want to enjoy some other types of power tubes? That is why we have tube selector here. LM-34IA has tube selector switch and you can choose to replace the standard EL34 with KT range of power tubes include KT66, KT70, KT90, KT100 and 6550. Different from other inputs Pre-In offers you a possibility to connect to some other Preamplifier so that you can the LM-34IA as a power amplifier.
Specially designed EI transformers for power supply and two EI output transformers with wide bandwidth are applied. Handmade construction with the finest point-to-point wiring and special audiophiles components has carefully been selected by our designers.
User bias control has been used for bias adjustment and one meter has been added to the top plate to allow you to monitor bias with ease.
Pathos Logos
Pathos Logos: Integrated amplifier (HiDac Optional)
Close to the spirit that has animated since its origin has always been involved in the search for new solutions and improvement of its machines for Music.
E with this approach that Pathos after more than ten years after the introduction of the integrated Pathos Logos presents its evolution MKII.
Pathos is not usual to introduce updated versions of its models except in the presence of substantial and meaningful new ideas to offer its loyal customers and in general to all lovers of good music.
Indeed behind the usual original design the new Logos MKII hide the introduction of a series of new solutions some thought in order to further enhance the sound of the amplifier and others to meet the demand for versatility and practicality that a demanding clientele pretends that is also present in a high-end device.
Finish: Padouk Wood or Black Front Panel
Pathos Classic One
Pathos Classic One – Integrated amplifier
After having won over the international audiophile community with state-of-the-art reference amplifiers, to conceive a product with a set price point as the main design limit has been a true challenge to Pathos.
The Classic One project was initiated to transfer, in a more affordable amplifier, all the know-how and expertise acquired developing reference products.
Classic One represents a new standard in its price category: it successfully blends in a single chassis a preamplifier and power amplifier, completely separated from each other and provided with their own individual power supplies.
The pre-stage – or, better, the preamplifier – is purely tube, balanced, pure Class A, extremely low noise, with high intrinsic linearity and without any feedback. It provides an exquisitely tube sound in terms of transparency, air, harmonics and refinement… in one word, musicality.
The power stage is a solid state power amplifier, high bias current, Class A/AB in order to adequately drive every load. It provides the sound with speed and dynamics, without influencing the tube nature of the sound. The volume control is motorised and remote controlled, the remote itself is in solid wood. Power supplies are over-dimensioned and stabilized.
Selected components, pure silver Pathos signal cable wiring, gold plated terminals, high-quality materials and refinement at its highest standard are additional benefits provided with the Classic One.
Together with such sound performance and overall quality, the Classic One is offered at a price that clearly demonstrates a philosophy of value for money. This is possible thanks to an aimed design approach, coupled with extremely accurate engineering and superior aesthetic form.
LINE MAGNETIC LM-212PA
LM-212PA -Mono Amplifier – Single Ended 212 – 1x32W
The LM-212PA is the «ultimate» monophonic amplifier from Line Magnetic, requiring more than two years of development. Its design is based on a Triode 212 mounted in Single Ended and «drived» by a 300B. In order to guarantee the durability of this exceptional tube, a sophisticated mechanical system protects it from shocks when not in use.
Finish: Silver